# How do I properly disassemble/re-assemble the Pod?

> You will use the draining tool provided in the tech bundle box to empty the water in the cover and hub. Be sure to have a bowl handy to catch any water that ...

Source: https://help.eightsleep.com/en_us/i-am-moving-how-do-i-properly-disassemble-the-pod-S18DYSxiI

Last updated: 2026-11-17T03:27:03.055Z

Are you getting ready to move or need some temporary storage for your Pod? Disassembling your Pod is as simple as set up. Here, you will find the steps to disconnect, drain, store, and reassemble all of your Pod components.

Before you start, make sure to have the items below available:

*   **Draining tool:** This comes included in your tech bundle box. See note below if unable to locate the drain tool.
    
*   **Vessel to collect water:** We recommend a large bowl or bucket. Don't worry if the bowl is too small. You can always stop releasing the water if your bowl is full.
    

![](https://cdn.kustomerhostedcontent.com/media/5b32c6759af69f723e861525/3fd8d04d6c50f49b24c995af7dbbc8cb.gif)

**Step 1: Disconnect**

Disconnecting the Hub and Cover will not release the water, although it may release a few drops. You can safely disconnect the two by holding the two sides of the cover water cord and pulling gently. Repeat the same if you have the Blanket or Pod Pillow cover(s).

  

**Step 2: Drain**

Follow the steps below for each of your products.

*   **
    
    **Cover**
    
    **

1.  It is very important to make sure the USB-C cables on the water cord do not get wet. Please ensure extra care to avoid. If water gets near, let air dry overnight before reconnecting to any power source.
    
2.  Place the water cord over a vessel to collect water (such as a large bowl or bucket). You do not need to remove the cover as long as most of the cord is lower than the cover surface.
    
3.  To begin releasing water, click the draining tool into the connectors at the end of the water cord. The water will flow freely as long as the drain tool remains connected. As the cover loses pressure, the water will slow to a trickle.
    
4.  Keep the water cord over the vessel until water no longer drains from the cord.
    
5.  When the water trickle stops, press down on the cover to try to push a bit more water out.
    
6.  Release the drain tool by clicking the buttons on both sides of the water cord.
    

\*Reach out for more details if you intend to store the cover for a longer duration.

*   ****Pod 6 Hub**** 

1.  Disconnect the power cord. Keep it with the Hub or cover to avoid losing it
    
2.  Remove the cap to allow airflow while draining
    
3.  Click the draining tool into the connectors at the back of the Hub
    
4.  Position the Hub over a bowl until the water no longer drains
    

*   ****Pod 5 or earlier generation Hub**** 

4.  Disconnect the power cord. Keep it with the Hub or cover to avoid losing it
    
5.  Remove and empty the water reservoir
    
6.  Click the draining tool into the connectors at the back of the Hub
    
7.  Position the Hub over a bowl until the water no longer drains
    

*   **
    
    **Pod Blanket**
    
    **

1.  For best results, we recommend keeping the Blanket flat on the bed as long as the water cord(s) are lower than the surface.
    
2.  Click the draining tool into one of the connectors at the end of the water cord attached to the Blanket over a bowl
    
3.  Keep the water cord over a bowl until the water no longer drains from the cord
    
4.  Gently press on the blanket to push a bit more water out.
    
5.  Repeat for the other side of the blanket
    

*   Pod Pillow Cover(s)
    

1.  For best results, we recommend keeping the Pod Pillow Cover flat on the bed as long as the water cord(s) are lower than the surface.
    
2.  Click the draining tool into one of the connectors at the end of the water cord attached to the Pod Pillow Cover over a bowl
    
3.  Keep the water cord over a bowl until the water no longer drains from the cord
    
4.  Gently press or tilt the Pod Pillow Cover to push a bit more water out.
    
5.  Release the drain tool by clicking the button on the side of the water cord
    
6.  If applicable, repeat for the other pillow
    

**Step 3: Store**

*   **
    
    **Cover**
    
    **

1.  Flip the cover over, placing the inside facing you.
    
2.  Tuck the water cord inside the cover to prevent damage
    
3.  Fold the cover in half lengthwise, bringing the right top corner over the left.
    
4.  Fold the cover in half once more, keeping it lengthwise.
    
5.  Gently roll the folded cover from bottom to top, creating a compact bundle.
    

*   **
    
    **Hub**
    
    **

1.  Dry and reinsert the water reservoir
    
2.  Place the Hub in the box. - If the Hub is going through the post or a moving company, we recommend padding the Hub either with the original shipping material or with bubble wrap, packing peanuts, or the like.
    

*   **
    
    **Pod Blanket**
    
    **

1.  Fold the Blanket in thirds so the water cords are in the center
    
2.  Either further fold or gently roll the folded cover, creating a compact bundle
    

*   Pod Pillow Cover
    

1.  Keep the cover cords in the center
    
2.  Fold or roll the Pod Pillow Cover cover for storage
    

**Step 4: Removing the Base (if applicable)**

1.  Ensure you have removed your mattress from your bed. We recommend having two people disassemble the Base.
    
2.  Remove the retainer bars and connector plate.
    
3.  Disconnect the Base from the Power Supply.
    
4.  Fold both sides of the Base over. If you were using the legs or levelers, unscrew and remove.
    
5.  Remove each side of the Base from your bed frame
    

**Step 5: Reassemble**

1.  Use the Eight Sleep app to reconnect your device(s).
    
2.  Set up your Hub and cover by fitting your cover over the mattress, securely connecting the Hub and cover cords and USB cable, adding water to the water reservoir, and plugging the Hub in.
    
3.  Connect your Hub to the wifi
    
4.  Force a priming session (settings > click on the Pod > maintenance)
    
5.  Click on Settings in the app
    
6.  Click the "+" button
    
7.  Select the device(s) you're setting up
    

**I lost the draining tool. How do I proceed?**

The Hub and Pod Blanket openings can release water when manually pressed. For the cover, there is an alternative method using household items to drain your cover if you're needing to drain it without the drain tool. Use four metal straws if available, as these will work best. If you have four pens available, you can use the non-pointed end to achieve this as well (Sharpies will provide the best result). Press the pens or straws into the cover openings to release the water.

Can’t find the drain tool or need further assistance? Reach out to our support team at [support@eightsleep.com](mailto:support@eightsleep.com), we are happy to help.
